Difference between pages "JTAG Samsung Galaxy Centura (SCH-S738C)" and "File:Active plugin.JPG"

From ForensicsWiki
(Difference between pages)
Jump to: navigation, search
m (Samsung Galaxy Centura SCH-S738C)
 
 
Line 1: Line 1:
== Samsung Galaxy Centura SCH-S738C ==
 
  
This phone is supported by the Tracfone network and uses a Qualcomm MSM7625A 800 MHz Snapdragon (S1) Processor. The phone has 4 GB of internal storage with a Samsung KMSJS000KM B308 MoviNAND flash memory chip. This phone is unsupported by RIFF Box for the JTAG process but can be imaged with the direct access plugin.
 
 
{| border="1" cellpadding="2"
 
|-
 
| [[ File:S738C_front.JPG | 200px ]]
 
|-
 
|}
 
 
=== Getting Started ===
 
 
 
What you need:
 
 
 
# Riff Box
 
# USB to Micro USB cord
 
 
 
=== NAND Dump Procedure ===
 
 
 
# Remove the rear cover, exposing the 7 phillips head screws.
 
# Remove the screws and the rear plastic casing with a plastic pry tool.
 
# Remove the two molex connectors attached on the right and top of the printed circuit board.
 
# Remove the printed circuit board from the screen casing exposing the nine TAPS on the reverse side. Note the small copper carrot indicating the direction of the TAPS.
 
# Connect the RIFF box to the JTAG pins.
 
# Connect the PCB to a Micro USB cord and power via a power supply.
 
# Start the "RIFF box" software.
 
# Power the PCB.
 
# Dump the NAND.
 
 
{| border="1" cellpadding="2"
 
|-
 
| [[ File:S738C_back.JPG | 600px ]]
 
|-
 
|}
 
 
{| border="1" cellpadding="2"
 
|-
 
| [[ File:S738C_case.JPG | 600px ]]
 
|-
 
|}
 
 
{| border="1" cellpadding="2"
 
|-
 
| [[ File:S738C_molex.JPG | 600px ]]
 
|-
 
|}
 
The TAPS order is as follows:
 
 
# 1=GND
 
# 2=NRST
 
# 3=TDO
 
# 4=TCK
 
# 5=TDI
 
# 6=TRST
 
# 7=RTCK
 
# 8=TMS
 
# 9=N/A
 
 
 
{| border="1" cellpadding="2"
 
|-
 
| [[ File:S738C_TAPS.JPG | 600px ]]
 
|-
 
|}
 
 
***Test has shown for the best results and fewer read errors, use short wires directly to the RIFF box ribbon interface.***
 
 
After the wires are connected to the board, the phone is powered by the USB connection. Plug the Micro USB into the USB connection on the device and then plug the phone into the USB port on the laptop.
 
 
 
Launch the Riff Box JTAG Manager and use the following settings:
 
 
 
* Navigate to the Useful Plugins tab
 
* Select the Direct JTAG Access to Flash Memory Plugin. Note the directions displayed in the window along with supported processors.
 
* Activate the plugin
 
* Choose the MSM7627A from the drop down menu on the right side ** Note this is not the processor but it will allow access the the memory.
 
* Select eMMC SDC3 (via chipset) from the Memory Type & Host drop down.
 
* Check Auto FullFlash size
 
* Select Connect & Flash ID. ** This will not flash the memory chip initially, but will only connect**
 
* Choose the read button from the bottom left corner. This will connect to the device and display the partitions and chip ID.
 
 
{| border="1" cellpadding="2"
 
|-
 
| [[ File:active_plugin.JPG | 800px ]]
 
|-
 
|}
 
 
{| border="1" cellpadding="2"
 
|-
 
| [[ File:SCH-S738C_Setting2.JPG | 800px ]]
 
|-
 
|}
 
 
{| border="1" cellpadding="2"
 
|-
 
| [[ File:SCH_S738C_Setting2.PNG | 800px ]]
 
|-
 
|}
 
 
 
 
=== Notes ===
 
 
 
The phone has a 4GB MoviNAND flash memory chip which should take approximately 24 hours to download. This takes much longer the normal because the direct access plugin functions at a much slower speed then normal JTAG methods. Test have found using shorter large wires and no intermediate PCB board increases performance.
 
 
 
=== References ===
 
*http://www.riffbox.org/
 

Latest revision as of 20:33, 23 December 2013