Difference between pages "Microsoft Windows Mobile" and "JTAG Huawei TracFone M866C"

From Forensics Wiki
(Difference between pages)
Jump to: navigation, search
(Cleaned up external links, headings)
 
(Huawei M866C - Ascend Y)
 
Line 1: Line 1:
Windows Mobile is an operating system that has both a look-and-feel and a programmer API that are similar to Microsoft Windows but which runs in a dramatically reduced footprint. Windows Mobile is the successor operating system to Windows CE.
+
== Huawei  H866C - Ascend Y ==
  
== Windows Mobile Versions ==
+
This phone is supported by the Tracfone. This uses a Qualcomm 7625A 800 MHz (S1) Processor and comes standard with Android version 2.3. This phone is unsupported by RIFF Box for the JTAG process for resurrector.
  
===Windows Mobile 2002===
+
{| border="1" cellpadding="2"
 +
|-
 +
| [[ File:Huawei-tracfone-m866c-front.JPG | 200px ]]
 +
|-
 +
|}
  
===Windows Mobile 2003===
+
=== Getting Started ===
  
===Windows Mobile 2003 Second Edition===
 
  
===Windows Mobile 5.0===
+
What you need:
  
===Windows Mobile 6.0===
 
Windows Mobile 6 is expected to be released in April 2007. Some users will be able to update their current Windows Mobile 5 to the new 6.0 version for free. WM6 will integrate tightly with Windows Vista.  Challenges facing forensic investigators are the support for VoIP and advanced multimedia.  While it is too early to offer details or experiences, it is touting to be more in line with the Blackberry "push" model then the previous Windows CE "pull" model.
 
  
==External Links==
+
# Riff Box
* [http://en.wikipedia.org/wiki/Windows_Mobile Wikipedia entry on Windows Mobile]
+
# USB to Micro USB cord
* [http://www.mypocketpcmobile.com/ MyPocketPCMobile.com]
+
 
 +
 
 +
=== NAND Dump Procedure ===
 +
 
 +
 
 +
# Remove the battery and peel the label back to expose the TAPS.
 +
# Connect the RIFF box to the PC via USB.
 +
# Connect the RIFF box to the PCB via the JTAG pins.
 +
# Connect the PCB to a Micro USB cord and power via a power supply.
 +
# Start the "RIFF box" software.
 +
# Power the PCB.
 +
# Dump the NAND.
 +
 
 +
 
 +
The TAPS are located under the battery, behind the Huawei phone label. The phone will be powered by a Micro USB cord from an AC battery charger.
 +
 
 +
 
 +
The TAPS order is as follows:
 +
 
 +
# 1=Not Used
 +
# 2=TCK
 +
# 3=GND
 +
# 4=TMS
 +
# 5=TDI
 +
# 6=TDO
 +
# 7=RTCK
 +
# 8=TRST
 +
# 9=NRST
 +
 
 +
 
 +
{| border="1" cellpadding="2"
 +
|-
 +
| [[ File:Hauwei_U866C_TAPS.jpg | 600px ]]
 +
|-
 +
|}
 +
 
 +
 
 +
After the wires are connected to the board, the phone is powered by the USB connection. Plug the Micro USB into the USB connection on the device and then plug the phone into a wall outlet. The phone should respond with the vibrator switch activating for less than a second.
 +
 
 +
 
 +
Launch the Riff Box JTAG Manager and use the following settings:
 +
 
 +
 
 +
* JTAG TCK Speed = RTCK
 +
* Resurrector Settings= Huawei U8655
 +
* Auto FullFlash size
 +
 
 +
{| border="1" cellpadding="2"
 +
|-
 +
| [[ File:M866C_setting.jpg | 800px ]]
 +
|-
 +
|}
 +
 
 +
 
 +
Advanced Settings:
 +
 
 +
 
 +
* Ignore Target IDCODE during Resurrection and DCC Loader operations
 +
 
 +
 
 +
{| border="1" cellpadding="2"
 +
|-
 +
| [[ File:huawei-tracfone-m865c-riff-advanced-settings.jpg | 600px ]]
 +
|-
 +
|}
 +
 
 +
 
 +
Then connect and get the ID, you should receive the dead body signal. Then read the memory.
 +
 
 +
 
 +
=== Notes ===
 +
 
 +
 
 +
The phone has a 512 MB NAND flash memory chip which should take approximately 30 minutes to download.
 +
 
 +
 
 +
=== References ===
 +
*http://www.phonescoop.com/phones/phone.php?p=3308
 +
*http://www.riffbox.org/

Latest revision as of 20:51, 25 November 2013

Contents

Huawei H866C - Ascend Y

This phone is supported by the Tracfone. This uses a Qualcomm 7625A 800 MHz (S1) Processor and comes standard with Android version 2.3. This phone is unsupported by RIFF Box for the JTAG process for resurrector.

Huawei-tracfone-m866c-front.JPG

Getting Started

What you need:


  1. Riff Box
  2. USB to Micro USB cord


NAND Dump Procedure

  1. Remove the battery and peel the label back to expose the TAPS.
  2. Connect the RIFF box to the PC via USB.
  3. Connect the RIFF box to the PCB via the JTAG pins.
  4. Connect the PCB to a Micro USB cord and power via a power supply.
  5. Start the "RIFF box" software.
  6. Power the PCB.
  7. Dump the NAND.


The TAPS are located under the battery, behind the Huawei phone label. The phone will be powered by a Micro USB cord from an AC battery charger.


The TAPS order is as follows:

  1. 1=Not Used
  2. 2=TCK
  3. 3=GND
  4. 4=TMS
  5. 5=TDI
  6. 6=TDO
  7. 7=RTCK
  8. 8=TRST
  9. 9=NRST


Hauwei U866C TAPS.jpg


After the wires are connected to the board, the phone is powered by the USB connection. Plug the Micro USB into the USB connection on the device and then plug the phone into a wall outlet. The phone should respond with the vibrator switch activating for less than a second.


Launch the Riff Box JTAG Manager and use the following settings:


  • JTAG TCK Speed = RTCK
  • Resurrector Settings= Huawei U8655
  • Auto FullFlash size
M866C setting.jpg


Advanced Settings:


  • Ignore Target IDCODE during Resurrection and DCC Loader operations


Huawei-tracfone-m865c-riff-advanced-settings.jpg


Then connect and get the ID, you should receive the dead body signal. Then read the memory.


Notes

The phone has a 512 MB NAND flash memory chip which should take approximately 30 minutes to download.


References